_______________________________________________________________________________________ 5
Single-Port, 40W, IEEE 802.3af/802.3at PSE
Controller with Integrated MOSFET
Note 2: This device is production tested at T
A
 = +25NC. Limits at T
A
 = -40NC and +85NC are guaranteed by design.
Note 3: If ILIM1 and ILIM2 are both unconnected, Class 5 detection is disabled. See the Class 5 PD Classification section and Table 3 for
details and settings.
Note 4: R
DOK
 = (V
OUT2
 - V
OUT1
)/(I
DET2
 - I
DET1
). V
OUT1
, V
OUT2
, I
DET2
, and I
DET1
 represent the voltage at OUT and the current at
DET during phase 1 and 2 of the detection, respectively.
Note 5: If Class 5 is enabled, this is the classification current thresholds from Class 4 to Class 5.
ELECTRICAL CHARACTERISTICS (continued)
(V
AGND
 - V
EE
 = 32V to 60V, T
A
 = -40NC to +85NC, all voltages are referenced to V
EE
, unless otherwise noted. Typical values are at
V
AGND
 - V
EE
 = +54V, T
A
 = +25NC. Currents are positive when entering the pin and negative otherwise.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL INPUTS/OUTPUTS (Voltages referenced to V
EE
)
Digital Input Low
V
IL
0.8
V
Digital Input High
V
IH
2.4
V
Internal Input Pullup Current
I
PU
Pullup current to internal digital supply to
set default values
3
5
7
FA
LED Output Low Voltage
V
LED_LOW
I
LED
 = 10mA, PWM disabled, port power-on
0.8
V
LED Output Leakage
I
LED_LEAK
PWM disabled, shutdown mode,
V
LED
 = 60V
10
FA
PWM Frequency
25
kHz
PWM Duty Cycle
6.25
%
TIMING
Startup Time
t
START
Time during which a current limit set to
420mA is allowed, starts when power is
turned on
50
60
70
ms
Fault Time
t
FAULT
Maximum allowed time for an overcurrent
condition set by I
CUT
 after startup
50
60
70
ms
Detection Reset Time
t
ME
Time allowed for the port voltage to reset
before detection starts
80
90
ms
Detection Time
t
DET
Maximum time allowed before detection is
completed
330
ms
Midspan Mode Detection Delay
t
DMID
2
2.2
2.4
s
Classification Time
t
CLASS
Time allowed for classification
19
23
ms
Mark Event Time
Time allowed for mark event
7
9
11
ms
V
EEUVLO
 Turn-On Delay
t
DLY
Time V
AGND
 must be above the V
EEUVLO
 
thresholds before the device operates
5.2
ms
Restart Timer
t
RESTART
Time the device waits before turning on
after an overcurrent fault
16 x
t
FAULT
ms
相关PDF资料
MAX5972AETE+T IC CONTROLLER INTERFACE 16TQFN
MAX5978ETJ+ IC CTLR HOT-SWAP 32TQFN
MAX5981BETE+ IC CTRLR PD IEEE 802.3AF 16TQFN
MAX5986AETE+ IC POE SWITCH PSE 16TQFN
MAX6509CAZK/V+T IC TEMP SWITCH RES-PROG 5TSOT
MAX6513TT075+T IC TEMP SWITCH REMOTE 6-TDFN
MAX6581TG9A+ IC TEMP SENSOR 8-CH PREC 24-TQFN
MAX6602UE9A+T IC TEMP MONITOR 5CH 16-TSSOP
相关代理商/技术参数
MAX5971AETI+T 功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5971AETI+W 制造商:Maxim Integrated Products 功能描述:IEEE802.3 AT PSE SWITCH - Rail/Tube
MAX5971AEVKIT 功能描述:电源管理IC开发工具 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
MAX5971AEVKIT+ 制造商:Maxim Integrated Products 功能描述:PD INTERFACE CONTROLLER - Boxed Product (Development Kits)
MAX5971BETI 制造商:Maxim Integrated Products 功能描述:
MAX5971BETI+ 功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5971BETI+T 功能描述:热插拔功率分布 IEEE 802.3af/at PSE Controller RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MAX5971BETI+W 制造商:Maxim Integrated Products 功能描述:SINGLE-PORT, 40W, IEEE 802.3AF/AT, PSE CONTROLLER WITH IC - Rail/Tube